Báo cáo tài liệu vi phạm
Giới thiệu
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
THỊ TRƯỜNG NGÀNH HÀNG
NÔNG NGHIỆP, THỰC PHẨM
Gạo
Rau hoa quả
Nông sản khác
Sữa và sản phẩm
Thịt và sản phẩm
Dầu thực vật
Thủy sản
Thức ăn chăn nuôi, vật tư nông nghiệp
CÔNG NGHIỆP
Dệt may
Dược phẩm, Thiết bị y tế
Máy móc, thiết bị, phụ tùng
Nhựa - Hóa chất
Phân bón
Sản phẩm gỗ, Hàng thủ công mỹ nghệ
Sắt, thép
Ô tô và linh kiện
Xăng dầu
DỊCH VỤ
Logistics
Tài chính-Ngân hàng
NGHIÊN CỨU THỊ TRƯỜNG
Hoa Kỳ
Nhật Bản
Trung Quốc
Hàn Quốc
Châu Âu
ASEAN
BẢN TIN
Bản tin Thị trường hàng ngày
Bản tin Thị trường và dự báo tháng
Bản tin Thị trường giá cả vật tư
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
NGÀNH HÀNG
NÔNG NGHIỆP, THỰC PHẨM
Gạo
Rau hoa quả
Nông sản khác
Sữa và sản phẩm
Thịt và sản phẩm
Dầu thực vật
Thủy sản
Thức ăn chăn nuôi, vật tư nông nghiệp
CÔNG NGHIỆP
Dệt may
Dược phẩm, Thiết bị y tế
Máy móc, thiết bị, phụ tùng
Nhựa - Hóa chất
Phân bón
Sản phẩm gỗ, Hàng thủ công mỹ nghệ
Sắt, thép
Ô tô và linh kiện
Xăng dầu
DỊCH VỤ
Logistics
Tài chính-Ngân hàng
NGHIÊN CỨU THỊ TRƯỜNG
Hoa Kỳ
Nhật Bản
Trung Quốc
Hàn Quốc
Châu Âu
ASEAN
BẢN TIN
Bản tin Thị trường hàng ngày
Bản tin Thị trường và dự báo tháng
Bản tin Thị trường giá cả vật tư
Thông tin
Tài liệu Xanh là gì
Điều khoản sử dụng
Chính sách bảo mật
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Composites Manufacturing - Materials, Product, and Process Engineering Part 9
Đang chuẩn bị liên kết để tải về tài liệu:
Composites Manufacturing - Materials, Product, and Process Engineering Part 9
Ngọc Hiền
65
2
pdf
Không đóng trình duyệt đến khi xuất hiện nút TẢI XUỐNG
Tải xuống
Tham khảo tài liệu 'composites manufacturing - materials, product, and process engineering part 9', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | as well as for uniform cooling rate. This will avoid the risk of part distortion and telegraphing of thickness changes through the surface. For one-piece Class A panels the nominal thickness is typically 0.14 in. For two-piece panels it is 0.08 to 0.12 in. for outer panels and 0.07 to 0.10 in. for inner panels. 3. Inner and outer radii. Sharp corners must be avoided during design. A minimum inside corner radius of 0.08 in. and minimum outside corner radius of 0.06 in. are recommended for better material flow along the corner as well as for ease in part removal. The general rule for paintability is to make inner and outer radii as large as possible without sacrificing part function. 4. Create mash-offs for hole location. A mash-off is a localized reduction in panel thickness for creating holes during secondary operation. It is a membrane-like thin area that can be easily removed. Charge can be placed directly over the mash-off area. This promotes a more homogeneous material flow through the hole location which improves mechanical properties around the hole. 6.8.8.4 Mold Design Compression molding is a match mold operation in which male and female molds are prepared. Because the charge is placed on the bottom half of the mold prior to molding there is no inlet port as in the RTM and SRIM processes. Entrapped air and excess resin escapes from the parting line as shown in Figure 6.68. The shear edge design shown in the figure reduces the need for edge trimming and thus aids in near-net-shape part molding. The shear edge closes before the flow front reaches the parting line and therefore does not allow reinforcements to escape. A stop block is designed to prevent damage to the mold during the mold closing operation. The mold is usually made of steel and is nickel or chrome plated to improve the surface finish of the molded part and the wear resistance of the mold. FIGURE 6.68 Shear edge in compression mold. 2002 by CRC Press LLC as well as for uniform cooling rate. This
TÀI LIỆU LIÊN QUAN
Composites Manufacturing - Materials, Product, and Process Engineering Part 1
Composites Manufacturing - Materials, Product, and Process Engineering Part 2
Composites Manufacturing - Materials, Product, and Process Engineering Part 3
Composites Manufacturing - Materials, Product, and Process Engineering Part 4
Composites Manufacturing - Materials, Product, and Process Engineering Part 5
Composites Manufacturing - Materials, Product, and Process Engineering Part 6
Composites Manufacturing - Materials, Product, and Process Engineering Part 7
Composites Manufacturing - Materials, Product, and Process Engineering Part 8
Composites Manufacturing - Materials, Product, and Process Engineering Part 9
Composites Manufacturing - Materials, Product, and Process Engineering Part 10
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.