Ảnh hưởng của phương pháp gia công lạnh đến sự chuyển biến tổ chức cacbit trong thép SKD11 sau khi tôi

Bài viết này trình bày kết quả nghiên cứu quá trình chuyển biến tổ chức cacbit và tính chất của thép SKD11 khi tôi ở nhiệt độ 1050oC với thời gian giữ nhiệt 30 phút và sau đó được xử lý lạnh ở các nhiệt độ (- 20oC; -80oC) với 2 chế độ thời gian khác nhau 2h và 24h. | TNU Journal of Science and Technology 227 02 156 - 164 EFFECTS OF SUBZERO TREATMENTS ON CACBIDE ORGANIZATION TRANSFER OF SKD11 STEEL AFTER QUENCHING METHOD Vu Van Khanh1 Tran Thi Mai2 Nguyen Xuan Truong2 1Nam Dinh University of Technology Education 2Instuitute of Energy and Mining Mechanical Engineering ARTICLE INFO ABSTRACT Received 14 10 2021 The carbide organization determines the hardness and wear resistance Revised 28 02 2022 of SKD11 steel. However depending on the heat treatment method this organization may change to improve the hardness of SKD11 Published 28 02 2022 steel. This paper presents the results of studying the carbide transformation process and properties of SKD11 steel when quenched KEYWORDS at 1050oC with a holding time of 30 minutes and then cold-treated at Cryogenic treatment temperatures -20oC -80oC with two different time modes 2h and 24h. The results show that In case SKD11 steel is tempered and kept Sub-zero Treatment heat inside the steel appears carbide organization mainly in the form Treatment of M7C3 and the hardness is about 57HRC. In the case of cold-treated Steel SKD11 SKD11 steel the residual martensite and austenitic solid solution in the steel has secreted a fine M3C2 carbide phase with size Carbide the amount of carbide tends to change depending on the temperature cold treatment -20oC 16 carbide -80oC 20 carbide . Extended sub-zero treatment times tend to increase the carbide content in steel slightly but not significantly. After cryogenic treatment at different temperatures steel samples have high hardness and stability above 63HRC. ẢNH HƯỞNG CỦA PHƯƠNG PHÁP GIA CÔNG LẠNH ĐẾN SỰ CHUYỂN BIẾN TỔ CHỨC CACBIT TRONG THÉP SKD11 SAU KHI TÔI Vũ Văn Khánh1 Trần Thị Mai2 Nguyễn Xuân Trường2 1Trường Đại học Sư phạm Kỹ thuật Nam Định 2 Viện Cơ khí Năng lượng và Mỏ - Vinacomin THÔNG TIN BÀI BÁO TÓM TẮT Ngày nhận bài 14 10 2021 Tổ chức cacbit quyết định đến độ cứng và độ chịu mài mòn của thép SKD11. Tuy nhiên tùy thuộc vào phương

Không thể tạo bản xem trước, hãy bấm tải xuống
TÀI LIỆU LIÊN QUAN
TÀI LIỆU MỚI ĐĂNG
3    57    2    28-03-2024
105    251    5    28-03-2024
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.