Báo cáo tài liệu vi phạm
Giới thiệu
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Sức khỏe - Y tế
Văn bản luật
Nông Lâm Ngư
Kỹ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
THỊ TRƯỜNG NGÀNH HÀNG
NÔNG NGHIỆP, THỰC PHẨM
Gạo
Rau hoa quả
Nông sản khác
Sữa và sản phẩm
Thịt và sản phẩm
Dầu thực vật
Thủy sản
Thức ăn chăn nuôi, vật tư nông nghiệp
CÔNG NGHIỆP
Dệt may
Dược phẩm, Thiết bị y tế
Máy móc, thiết bị, phụ tùng
Nhựa - Hóa chất
Phân bón
Sản phẩm gỗ, Hàng thủ công mỹ nghệ
Sắt, thép
Ô tô và linh kiện
Xăng dầu
DỊCH VỤ
Logistics
Tài chính-Ngân hàng
NGHIÊN CỨU THỊ TRƯỜNG
Hoa Kỳ
Nhật Bản
Trung Quốc
Hàn Quốc
Châu Âu
ASEAN
BẢN TIN
Bản tin Thị trường hàng ngày
Bản tin Thị trường và dự báo tháng
Bản tin Thị trường giá cả vật tư
Tìm
Danh mục
Kinh doanh - Marketing
Kinh tế quản lý
Biểu mẫu - Văn bản
Tài chính - Ngân hàng
Công nghệ thông tin
Tiếng anh ngoại ngữ
Kĩ thuật công nghệ
Khoa học tự nhiên
Khoa học xã hội
Văn hóa nghệ thuật
Y tế sức khỏe
Văn bản luật
Nông lâm ngư
Kĩ năng mềm
Luận văn - Báo cáo
Giải trí - Thư giãn
Tài liệu phổ thông
Văn mẫu
NGÀNH HÀNG
NÔNG NGHIỆP, THỰC PHẨM
Gạo
Rau hoa quả
Nông sản khác
Sữa và sản phẩm
Thịt và sản phẩm
Dầu thực vật
Thủy sản
Thức ăn chăn nuôi, vật tư nông nghiệp
CÔNG NGHIỆP
Dệt may
Dược phẩm, Thiết bị y tế
Máy móc, thiết bị, phụ tùng
Nhựa - Hóa chất
Phân bón
Sản phẩm gỗ, Hàng thủ công mỹ nghệ
Sắt, thép
Ô tô và linh kiện
Xăng dầu
DỊCH VỤ
Logistics
Tài chính-Ngân hàng
NGHIÊN CỨU THỊ TRƯỜNG
Hoa Kỳ
Nhật Bản
Trung Quốc
Hàn Quốc
Châu Âu
ASEAN
BẢN TIN
Bản tin Thị trường hàng ngày
Bản tin Thị trường và dự báo tháng
Bản tin Thị trường giá cả vật tư
Thông tin
Tài liệu Xanh là gì
Điều khoản sử dụng
Chính sách bảo mật
0
Trang chủ
Kỹ Thuật - Công Nghệ
Cơ khí - Chế tạo máy
Heat and Mass Transfer Modeling and Simulation Part 8
Đang chuẩn bị liên kết để tải về tài liệu:
Heat and Mass Transfer Modeling and Simulation Part 8
Quốc Tuấn
59
20
pdf
Không đóng trình duyệt đến khi xuất hiện nút TẢI XUỐNG
Tải xuống
Tham khảo tài liệu 'heat and mass transfer modeling and simulation part 8', kỹ thuật - công nghệ, cơ khí - chế tạo máy phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả | Optimal Design of Cooling Towers 131 The prediction of power fan cost using the Poppe s method is higher than with the Merkel s method because more air is estimated for the same range this means that the cooling capacity of the inlet air in the Merkel s method is overestimated and the outlet air is oversaturated. This is proved by the solution of Equations 1 - 3 using the results obtained Tw T . m and ma from the Merkel s method and plotting the dry and wet bulb air temperatures for the solution intervals. Notice in Figure 6 that the air saturation Twb Ta is obtained before of the outlet point of the packing section. Fig. 6. Evaporate profile respect to air flow rate and range Fig. 7. Sensitivity analysis of the evaporate rate with respect to air flowrate and range With respect to the capital cost for cases 1 and 6 the estimations obtained using the Poppe s method are more expensive because of the higher air flowrate area and height packing. However for examples 3 and 4 both capital and operating costs are predicted at lower levels with the Poppe s method the capital cost is lower because the inlet air is relatively dry and therefore it can process higher ranges with low air flowrates which requires a lower packing volume. This can be explained because of the effect that the range and air flow rate have in the packing volume and the effect that the range has in the capital cost of the towers 132 Heat and Mass Transfer - Modeling and Simulation see Figure 8a 8b and 8c . Notice in Figure 9 that there exists an optimum value for the range to determine the minimum capital cost. Fig. 8. Air temperature profile in the packing section Optimal Design of Cooling Towers 133 Examples 1 2 3 Merkel Poppe Merkel Poppe Merkel Poppe Q kW 3400 3400 3400 3400 3400 3400 Ta in C 22 22 17 17 22 22 . Twb in C 12 12 12 12 7 7 TMPI C 65 65 65 65 65 65 Q TMPO C 30 30 30 30 30 30 DTMIN C 10 10 10 10 10 10 win kg water kg dry air 0.0047 0.0047 0.0067 0.0067 0.0002 0.0002 Tw in C 50 38.8866 .
TÀI LIỆU LIÊN QUAN
Heat and Mass Transfer Modeling and Simulation Part 1
Heat and Mass Transfer Modeling and Simulation Part 2
Heat and Mass Transfer Modeling and Simulation Part 3
Heat and Mass Transfer Modeling and Simulation Part 4
Heat and Mass Transfer Modeling and Simulation Part 5
Heat and Mass Transfer Modeling and Simulation Part 6
Heat and Mass Transfer Modeling and Simulation Part 7
Heat and Mass Transfer Modeling and Simulation Part 8
Heat and Mass Transfer Modeling and Simulation Part 9
Heat and Mass Transfer Modeling and Simulation Part 10
Đã phát hiện trình chặn quảng cáo AdBlock
Trang web này phụ thuộc vào doanh thu từ số lần hiển thị quảng cáo để tồn tại. Vui lòng tắt trình chặn quảng cáo của bạn hoặc tạm dừng tính năng chặn quảng cáo cho trang web này.